Edelbrock Automobile Parts 15012 User Manual

TURBOCHARGER TURBINE INLET STUD KIT  
For Exhaust Manifold To Turbine Inlet  
Catalog # 15012  
INSTALLATION INSTRUCTIONS  
Description: Contains the necessary hardware to mount the turbine inlet to the exhaust manifold. The hardware is constructed of  
high-quality stainless steel and can be used with any Garrett T25 or T28 Turbocharger.  
Kit Contents:  
Qty.  
Description  
1.45”  
K 4 Stud, 8mm x 1.25 x 1.45” long  
K 4 Nut, 8mm x 1.25  
K 4 Washer, 8mm  
INSTALLATION:  
Towards Exhaust  
Manifold  
Towards Turbine  
Inlet  
1. Hand tighten the 1.45” long studs into the exhaust  
manifold, with the shorter threads towards the manifold  
(See Fig. 1).  
Fig. 1  
2. When attaching the turbocharger to the exhaust manifold,  
and the turbo outlet elbow to the turbocharger, use an 8mm  
washer under each nut, and hand tighten the 8mm x 1.25  
nuts onto the studs.  
Edelbrock Corporation  
2700 California St. • Torrance • CA • 90503  
Tech Line: 1-800-416-8628  
3. Torque the 8mm x 1.25 nuts to 190 inch/lbs. (approximately  
16 ft/lbs).  
E-Mail: Edelbrock@Edelbrock.com  
Catalog #15012  
Rev. 5/05 - RS/mc  
©2005 Edelbrock Corporation  
Brochure #63-0391  
TURBOCHARGER TURBINE INLET STUD KIT  
For Exhaust Manifold To Turbine Inlet  
Catalog # 15012  
INSTALLATION INSTRUCTIONS  
Description: Contains the necessary hardware to mount the turbine inlet to the exhaust manifold. The hardware is constructed of  
high-quality stainless steel and can be used with any Garrett T25 or T28 Turbocharger.  
Kit Contents:  
Qty.  
Description  
1.45”  
K 4 Stud, 8mm x 1.25 x 1.45” long  
K 4 Nut, 8mm x 1.25  
K 4 Washer, 8mm  
INSTALLATION:  
Towards Exhaust  
Manifold  
Towards Turbine  
Inlet  
1. Hand tighten the 1.45” long studs into the exhaust  
manifold, with the shorter threads towards the manifold  
(See Fig. 1).  
Fig. 1  
2. When attaching the turbocharger to the exhaust manifold,  
and the turbo outlet elbow to the turbocharger, use an 8mm  
washer under each nut, and hand tighten the 8mm x 1.25  
nuts onto the studs.  
Edelbrock Corporation  
2700 California St. • Torrance • CA • 90503  
Tech Line: 1-800-416-8628  
3. Torque the 8mm x 1.25 nuts to 190 inch/lbs. (approximately  
16 ft/lbs).  
E-Mail: Edelbrock@Edelbrock.com  
Catalog #15012  
Rev. 5/05 - RS/mc  
©2005 Edelbrock Corporation  
Brochure #63-0391  
 

Craftsman Saw 31521222 User Manual
Curtis Flat Panel Television LCDVD2224A User Manual
Cypress Computer Hardware STK11C68 5 User Manual
Dual Stereo Receiver XDVD8181 User Manual
Dynex Network Card DX UC104 User Manual
Fender Musical Instrument Amplifier B DEC 30 User Manual
Ford Automobile 2000 Escort User Manual
Frontier Labs Spreader MS1102G User Manual
GE Oven JKP45 User Manual
GE Ventilation Hood ZV755SPSS User Manual